![Filename=2009-01-01_10-26-24.JPG
Filesize=774KiB
Dimensions=2816x2112
Date added=Feb 13, 2009 2009-01-01_10-26-24.JPG](albums/TruckConversion/MotorMount/thumb_2009-01-01_10-26-24.JPG)
Motor-Motor mount finished3089 viewsPainted all prettyFeb 13, 2009
|
|
![Filename=2008-12-31_17-07-06.JPG
Filesize=777KiB
Dimensions=2816x2112
Date added=Feb 13, 2009 2008-12-31_17-07-06.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-31_17-07-06.JPG)
Motor-Motor mount drilled2376 viewsMounting holes drilled and primer applied.Feb 13, 2009
|
|
![Filename=2008-12-30_20-18-04.JPG
Filesize=829KiB
Dimensions=2816x2112
Date added=Feb 13, 2009 2008-12-30_20-18-04.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-30_20-18-04.JPG)
Bigger holes in the Impulse 92150 viewsWe decided that the rather small bolt holes in the end bells of the Impulse 9" motors were just too small.
So we drilled and tapped all of them out to a 7/16" bolt thread.Feb 13, 2009
|
|
![Filename=2008-12-30_17-53-22.JPG
Filesize=965KiB
Dimensions=2816x2112
Date added=Feb 13, 2009 2008-12-30_17-53-22.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-30_17-53-22.JPG)
Motor-Motor mount test fit2579 viewsHow it fits on one of the motors.Feb 13, 2009
|
|
![Filename=2008-12-29_16-04-20.JPG
Filesize=957KiB
Dimensions=2816x2112
Date added=Feb 13, 2009 2008-12-29_16-04-20.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-29_16-04-20.JPG)
Motor-Motor mount welded2220 viewsHere is the mostly finished mount all welded together.Feb 13, 2009
|
|
![Filename=2008-12-28_16-49-30.JPG
Filesize=833KiB
Dimensions=2816x2112
Date added=Feb 13, 2009 2008-12-28_16-49-30.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-28_16-49-30.JPG)
Motor-Motor mount access holes2444 viewsIt was interesting putting the access holes in the mount.Feb 13, 2009
|
|
![Filename=2008-12-28_15-04-10.JPG
Filesize=818KiB
Dimensions=2816x2112
Date added=Feb 13, 2009 2008-12-28_15-04-10.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-28_15-04-10.JPG)
Motor-Motor mount rough2454 viewsHere is the mount after some work in the lathe on both the raw pieces.Feb 13, 2009
|
|
![Filename=2008-12-27_11-58-40.JPG
Filesize=919KiB
Dimensions=2112x2816
Date added=Feb 13, 2009 2008-12-27_11-58-40.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-27_11-58-40.JPG)
Motor-Motor mount body2327 viewsAnd a piece of old iron pipe from the same place.Feb 13, 2009
|
|
![Filename=2008-12-27_11-47-24.JPG
Filesize=963KiB
Dimensions=2112x2816
Date added=Feb 13, 2009 2008-12-27_11-47-24.JPG](albums/TruckConversion/MotorMount/thumb_2008-12-27_11-47-24.JPG)
Motor-Motor mount ends3196 viewsWe started with some scrap plate steel from the local recycle place.Feb 13, 2009
|
|
|
|
|
|